CCNA New

CCNA New -- 18 Questions

Question 1

What are three components that comprise the SNMP framework? (Choose three)

A) MIB

B) agents

C) set

D) AES

E) supervisor

F) manager

Question 2

What SNMP message alerts the manager to a condition on the network?

A) response

B) get

C) trap

D) capture

Question 3

What authentication type is used by SNMPv2 ?

A) HMAC-MD5

B) HMAC-SHA

C) CBC-DES

D) community strings

Question 4

A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2?

A) interface FastEthernet0/1
channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk

B) interface FastEthernet0/1
channel-group 2 mode auto
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
channel-group 2 mode auto
switchport trunk encapsulation dot1q
switchport mode trunk

C) interface FastEthernet0/1
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEternet0/2
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk

D) interface FastEthernet0/1
channel-group 1 mode passive
switchport trunk encapsulation dot1q
swithcport mode trunk
interface FastEthernet0/2
channel-group 1 mode passive
switchport trunk encapsulation dot1q
switchport mode trunk

Question 5

Which two statements about the OSPF Router ID are true ? (Choose two)

A) it identifies the source of a Type 1 LSA

B) it should be the same on all routers in an OSPF routing instance

C) By default, the lowest IP address on the router becomes the OSPF Router ID

D) The router automatically chooses the IP address of a loopback as the OSPF Router ID.

Question 6

Which parameter can be different on ports with an EtherChannel?

A) speed

B) DTP negotiation settings

C) trunk encapsulation

D) duplex

Question 7

What are two benefits of using a single OSPF are network design ? (Choose two)

A) It is less CPU intensive for routers in the single area

B) It reduces the types of LSAs that are generated

C) it removes the need for virtual links

D) it increases LSA response times.

E) it reduces the number of required OSPF neighbor adjacencies.

Question 8

A) interface FastEthernet 0/3
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk

A) interface FastEthernet 0/3
channel-group 2 mode passive
switchport trunk encapsulation dot1q
switchport mode trunk

A) interface FastEthernet 0/3
channel-group 2 mode active
switchport trunk encapsulation dot1q
switchport mode trunk

A) interface FastEthernet 0/3
channel-group 2 mode on
switchport trunk encapsulation dot1q
switchport mode trunk

Question 9

A network administrator creates a Layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured ?

A) the port-channel 1 interface

B) the highest number member interface

C) all member interfaces

D) lowest number member interface

Question 10

What command sequence will configure a router to run OSPF and add network 10.1.1.0/24 to area 0 ?

A) router ospf area 0
network 10.1.1.0 255.255.255.0 area 0

B) router ospf
network 10.1.1.0 0.0.0.255

C) router ospf 1
network 10.1.1.0 0.0.0.255 area 0

D) router ospf area 0
network 10.1.1.0 0.0.0.255 area 0

E) router ospf
network 10.1.1.0 255.255.255.0 area 0

D) router ospf 1
network 10.1.1.0 0.0.0.255

Question 11

if the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID

A) 192.168.1.1

B) 172.16.1.1

C) 1.1.1.1

D) 2.2.2.2

Question 12

A) SW1's Fa0/1 interface is administratively shut down

B) There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces

C) There is an MTU mismatch between SW's Fa0/1 and SW2's Fa0/2 interfaces

D) There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces

Question 13

What OSPF command, when configured, will include all interfaces into area 0?

A) network 0.0.0.0 255.255.255.255 area 0

B) network 0.0.0.0 0.0.0.0 area 0

C) network 255.255.255.255 0.0.0.0 area 0

D) network all-interfaces area 0

Question 14

Which statement describes the process ID that is used to run OSPF on a router?

A) it is globally significant and is used to represent the AS number.

B) it is locally significant and is used to identify an instance of the OSPF database.

C) it is globally significant and is used to identify OSPF stub areas.

D) it is locally significant and must be the same throughout an area

Question 15

What is SNMPv2 authentication protocol?

A) Community Strings

B) HMAC-MD5

C) HDMAC-SHA

Question 16

In which solution is a router ACL used?

A) protecting a server from unauthrized access

B) controlling path selection, based on the route metric.

C) reducing router CPU utilization.

D) filtering packets that are passing through a router

Question 17

A) 190.172.32.10

B) 208.149.23.162

C) 208.149.23.194

D) 220.173.149.10

Question 18

Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts to ping between the hosts are unsuccessful. What two things can be done to allow communications between the hosts? (Choose two)

A) Replace the straight-through cable with with a crossover cable

B) Change the subnet mask of the hosts to /25

C) Change the subnet mask of the hosts to /26

D) Change the address of Workstation A to 192.0.2.15

E) Change the address of Workstation B to 192.0.2.111