CCNA Introduction

CCNA Introduction - 14 Questions

Question 1

Which layer in OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communciation ?

A) transport

B) network

C) presentation

D) session

E) application

Question 2

A network interface port has a collision detection and carrier sensing enabled on a shared twister pair network. From this statement, what is known about network interface port?

A) This is a 10 Mb/s switch port

B) This is a 100 Mb/s switch port

C) This is an Ethernet port operating at half duplex

D) This is an Ethernet port operating at full duplex

E) This is a port on network interface card in a PC

Question 3

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer tid this happen?

A) physical

B) session

C) data link

D) transport

E) network

Question 4

Which of the following correctly describe steps in the OSI data encapsulation process? (Chosse two)

A) The transport layer divides a data stream into segments and may add reliability and flow control information.

B) The data link layer adds physical source and destination addresses and an FCS to the segment.

C) Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related information.

D) Packets are created when the network layer adds Layer 3 addresses and control information to a segment.

E) The presentation layer translates bits into voltages for transmission across the physical link

Question 5

Refer to the graphic.

Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server ?

A) The MAC address of the server network interface.

B) The MAC address of host A.

C) The MAC address of router interface e1

D) The MAC address of router interface e0

Question 6

Refer to the exhibit.

What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two)

Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server ?

A) The number of broadcast domains would remain the same.

B) The number of collisions domains would increase.

C) The number of collision domains would decrease.

D) The number of broadcast domains would decrease.

E) The number of collision domains would remain the same.

F) The number of broadcast domains would increase.

Question 7

For what two purposes does the Ethernet protocol use physical addresses? (Choose two)

A) to uniquely identify devices at Layer 2.

B) to allow communication with devices on a different network

C) to differentiate a Layer 2 frame from a Layer 3 packet.

D) to establish a priority system to determine which device gets to transmit first

E) to allow communication between different devices on the same network

F) to allow detection of a remote device when its physical address is unknown

Question 8

In an Ethernet network, under what two scenarios can devices transmit? (Choose two)

A) When they receive a special token.

B) when there is a carrier

C) when they detect no other devices are sending.

D) when the medium is idle

E) when the server grants access

Question 9

Which of the following statements describe the network shown in the graphic?.

What are the proper statements? (Choose two)

A) There are two broadcast domains in the network.

B) There are four broadcast domains in the network.

C) There are six broadcast domains in the network.

D) There are four collision domains in the network.

E) There are five collision domains in the network.

F) There are seven collision domains in the network.

Question 10

How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches?

A) One

B) Six

C) Twelve

D) Two

Question 11

What is the first 24 bits in a MAC address called?

A) NIC

B) BIA

C) OUI

D) VAI

Question 12

Refer to the exhibit. What type of connection would be supported by the cable diagram shown?

A) PC to router

B) PC to switch

C) Server to router

D) Router to router

Question 13

Refer to the exhibit. What type of connection would be supported by the cable diagram shown?

A) PC to router

B) PC to switch

C) Server to router

D) Switch to router

Question 14

Which functions do routers perform in a network? (Choose two)

A) packet switching.

B) access layer security.

C) path selection.

D) VLAN membership assignment.

E) bridging between LAN segments.

F) microsegmentation of broadcast domains